🚚 Free Worldwide Shipping on All Orders!Shop Now
PowerTrays Dual BantamX/SourceLT PowerTray - 4Runner/FJ Cruiser/GX
PowerTrays Dual BantamX/SourceLT PowerTray - 4Runner/FJ Cruiser/GX
Whats better than having the all new sPOD BantamX/Source LT powering all your off road accessories? How about having two Bantam's powering all your off road accessories!
sPOD has done it again with their new solid state Power Distribution System. The Bantam brings a whole new level of control to your vehicles accessories. Also, with less than half the footprint of sPOD's renowned Source SE System, the small size of the sPOD Bantam makes it a perfect choice for any adventure vehicle.
This product is for the PowerTray Mounting Platform, Support Leg, and mounting hardware.
Does not include the BantamX/SourceLT.
Features:
- Black Powder Coat Finish - PowerTrays uses a high quality fine textured black powder coat to match your other accessories.
- PEM® Fasteners - Pressed into the PowerTray, genuine PEM fasteners Allow you to secure the BantamX directly to the PowerTray for a clean low-profile installation.
- 1/8th Inch 5052 Aircraft Aluminum - Possibly a little overkill to use for mounting electrical accessories that tend to weigh in the ounces, not pounds. But with a weight coming in at 3X lighter than steel and corrosion resistance far superior to even stainless steel, aluminum is the clear choice for weathering the harsh conditions we put our vehicles though.
- Waterjet manufacturing - Guarantees precise cuts with an accuracy of ±0.003", which is why it is used globally in many industries for intricate designs and jobs which require high tolerances.
- Chamfered edges - To avoid sharp edges PowerTrays chamfers all jagged edges and corners by hand with a specialized high-speed router bit. So you don't have to worry about cutting your hands or scratching your vehicles paint during installation. Also with a 45° chamfer on the edges you minimize the risk of vibration wearing though the protective sleeving on cables and wires which would short out the circuit.
- Perfect fit - Don't sacrifice access to your factory fuse block with other mounts! Each PowerTray is designed around your factory components.
- Unparalleled stability - Utilizing three points of contact, you can be sure that your valuable electronics are safe and supported by including an additional support leg that secures the far-side of the tray to the lower inner fender.
- High Quality JIS Class 10.9 Steel Hardware - Your entire Toyota is built with JIS (Japanese Industrial Standard) hardware so why should your aftermarket parts be any different.
This PowerTray will fit the following vehicles:
- Toyota FJ Cruiser 07-14 with Automatic Transmission
- Unfortunately manual transmission FJ's have a clutch fluid reservoir mounted in the same location the PowerTray is designed to install.
- Note: FJ cruiser's with the rear 400w inverter may have a small relay box bolted to the fender that will need trimmed.
- Toyota 4th and 5th gen 4Runner's 03-24
- Note: 2020+ 4runners have an additional relay/fuse box located on the fender that will need to be relocated closer to the cab of the vehicle in order to install this PowerTray.
- Lexus GX470 03-09 and GX460 10-13
- Note: These vehicles may have a plastic vanity cover that will need to be removed and discarded. But nothing should actually hinder installation.
$85.08
Original: $243.10
-65%PowerTrays Dual BantamX/SourceLT PowerTray - 4Runner/FJ Cruiser/GX—
$243.10
$85.08PowerTrays Dual BantamX/SourceLT PowerTray - 4Runner/FJ Cruiser/GX
PowerTrays Dual BantamX/SourceLT PowerTray - 4Runner/FJ Cruiser/GX
Whats better than having the all new sPOD BantamX/Source LT powering all your off road accessories? How about having two Bantam's powering all your off road accessories!
sPOD has done it again with their new solid state Power Distribution System. The Bantam brings a whole new level of control to your vehicles accessories. Also, with less than half the footprint of sPOD's renowned Source SE System, the small size of the sPOD Bantam makes it a perfect choice for any adventure vehicle.
This product is for the PowerTray Mounting Platform, Support Leg, and mounting hardware.
Does not include the BantamX/SourceLT.
Features:
- Black Powder Coat Finish - PowerTrays uses a high quality fine textured black powder coat to match your other accessories.
- PEM® Fasteners - Pressed into the PowerTray, genuine PEM fasteners Allow you to secure the BantamX directly to the PowerTray for a clean low-profile installation.
- 1/8th Inch 5052 Aircraft Aluminum - Possibly a little overkill to use for mounting electrical accessories that tend to weigh in the ounces, not pounds. But with a weight coming in at 3X lighter than steel and corrosion resistance far superior to even stainless steel, aluminum is the clear choice for weathering the harsh conditions we put our vehicles though.
- Waterjet manufacturing - Guarantees precise cuts with an accuracy of ±0.003", which is why it is used globally in many industries for intricate designs and jobs which require high tolerances.
- Chamfered edges - To avoid sharp edges PowerTrays chamfers all jagged edges and corners by hand with a specialized high-speed router bit. So you don't have to worry about cutting your hands or scratching your vehicles paint during installation. Also with a 45° chamfer on the edges you minimize the risk of vibration wearing though the protective sleeving on cables and wires which would short out the circuit.
- Perfect fit - Don't sacrifice access to your factory fuse block with other mounts! Each PowerTray is designed around your factory components.
- Unparalleled stability - Utilizing three points of contact, you can be sure that your valuable electronics are safe and supported by including an additional support leg that secures the far-side of the tray to the lower inner fender.
- High Quality JIS Class 10.9 Steel Hardware - Your entire Toyota is built with JIS (Japanese Industrial Standard) hardware so why should your aftermarket parts be any different.
This PowerTray will fit the following vehicles:
- Toyota FJ Cruiser 07-14 with Automatic Transmission
- Unfortunately manual transmission FJ's have a clutch fluid reservoir mounted in the same location the PowerTray is designed to install.
- Note: FJ cruiser's with the rear 400w inverter may have a small relay box bolted to the fender that will need trimmed.
- Toyota 4th and 5th gen 4Runner's 03-24
- Note: 2020+ 4runners have an additional relay/fuse box located on the fender that will need to be relocated closer to the cab of the vehicle in order to install this PowerTray.
- Lexus GX470 03-09 and GX460 10-13
- Note: These vehicles may have a plastic vanity cover that will need to be removed and discarded. But nothing should actually hinder installation.
Product Information
Product Information
Shipping & Returns
Shipping & Returns
Description
PowerTrays Dual BantamX/SourceLT PowerTray - 4Runner/FJ Cruiser/GX
Whats better than having the all new sPOD BantamX/Source LT powering all your off road accessories? How about having two Bantam's powering all your off road accessories!
sPOD has done it again with their new solid state Power Distribution System. The Bantam brings a whole new level of control to your vehicles accessories. Also, with less than half the footprint of sPOD's renowned Source SE System, the small size of the sPOD Bantam makes it a perfect choice for any adventure vehicle.
This product is for the PowerTray Mounting Platform, Support Leg, and mounting hardware.
Does not include the BantamX/SourceLT.
Features:
- Black Powder Coat Finish - PowerTrays uses a high quality fine textured black powder coat to match your other accessories.
- PEM® Fasteners - Pressed into the PowerTray, genuine PEM fasteners Allow you to secure the BantamX directly to the PowerTray for a clean low-profile installation.
- 1/8th Inch 5052 Aircraft Aluminum - Possibly a little overkill to use for mounting electrical accessories that tend to weigh in the ounces, not pounds. But with a weight coming in at 3X lighter than steel and corrosion resistance far superior to even stainless steel, aluminum is the clear choice for weathering the harsh conditions we put our vehicles though.
- Waterjet manufacturing - Guarantees precise cuts with an accuracy of ±0.003", which is why it is used globally in many industries for intricate designs and jobs which require high tolerances.
- Chamfered edges - To avoid sharp edges PowerTrays chamfers all jagged edges and corners by hand with a specialized high-speed router bit. So you don't have to worry about cutting your hands or scratching your vehicles paint during installation. Also with a 45° chamfer on the edges you minimize the risk of vibration wearing though the protective sleeving on cables and wires which would short out the circuit.
- Perfect fit - Don't sacrifice access to your factory fuse block with other mounts! Each PowerTray is designed around your factory components.
- Unparalleled stability - Utilizing three points of contact, you can be sure that your valuable electronics are safe and supported by including an additional support leg that secures the far-side of the tray to the lower inner fender.
- High Quality JIS Class 10.9 Steel Hardware - Your entire Toyota is built with JIS (Japanese Industrial Standard) hardware so why should your aftermarket parts be any different.
This PowerTray will fit the following vehicles:
- Toyota FJ Cruiser 07-14 with Automatic Transmission
- Unfortunately manual transmission FJ's have a clutch fluid reservoir mounted in the same location the PowerTray is designed to install.
- Note: FJ cruiser's with the rear 400w inverter may have a small relay box bolted to the fender that will need trimmed.
- Toyota 4th and 5th gen 4Runner's 03-24
- Note: 2020+ 4runners have an additional relay/fuse box located on the fender that will need to be relocated closer to the cab of the vehicle in order to install this PowerTray.
- Lexus GX470 03-09 and GX460 10-13
- Note: These vehicles may have a plastic vanity cover that will need to be removed and discarded. But nothing should actually hinder installation.
